E sampler item 263

This machine measures dust levels in ambient air.
The E-Sampler uses both a laser and gravimetric analyzer to monitor aerosols and particles in real time.
It is equipped with a data acquisition unit. Life of the battery (included) is 30 hours.
The device is suitable for taking readings both inside and outside buildings. It also indicates ambient temperature, atmospheric pressure and relative humidity.

Specification

– Measuring Range : 0 – 0.5, 0 – 1, 0 – 10 and 0 – 100 mg/m3 (automatic).
– Unit : mg/m3
– Detection Limit : 1 μg/m3
– Sampling Flow-rate : from 1 to 3.5 l/min, temperature and pressure compensated.
– Sampling Period : 1 s
– Accuracy : 3 μg/m3 or 2% of the reading
– Analysis Filter : 47 mm
– Ambient Temperature : -30 to +50 °C
– Atmospheric Pressure : 600 to 1040 hPa
– Data storage : 10,000 readings.
– Internal Pump : yes
– Communication interface : yes
– Software : yes
– Packaged weight : 25 kg
– Number of packages : 2

 

Key Points

– Auto zero and self-calibration (concealable filter) programmable from 15 min to 24 hours

Express Dilution System Item 842

Sonic nozzle dilution probe.
Ideal for reducing concentrations or drying a condensable gas by cooling.
 

Specification

– Dilution ratios 1/16 to 1/300
– Requires on site air instrument zero at 5 bar
– Requires high concentration calibration gas to set the dilution ratio
– Consumption : 6 l/min of dilutant air
– Consumption : 20 to 500 cc of calibration gas
– Packaged weight : 30 kg, 1 crate

 

Key Points

– An instrument air system is recommended.

42C item 235

This machine can measure NO, NO2 and NOx.
The Thermo 42C uses the principle of chemiluminescence.
It alternately measures NO (directly) and then NOx (via the converter).
It displays the 3 parameters continuously, for NO, NO2 and NOx.
It can be used after a dilution system on a high concentration application (such as emissions).

Specification

– Measurement Range : programmable from 0 – 0.05 ppm to 0 – 100 ppm.
– Units : ppb or mg/m3 programmable
– Detection Limit : 0.4 ppb
– Data storage : 5000 measurement points
– Internal Pump: yes
– Analog Output : yes
– Communication interface : yes
– Software : Yes
– Packaged weight : 28 kg
– Number of packages : 1
– Recommended for use with : 622, 840, 921, 927.

Key Points

– Menus for setting parameters and optical and electronic diagnostics
– Automatic range switchover
– Fast response time, linearity on all ranges
– Reduced sensitivity to interference
 

Ultramat 23 item 120 121 122

This continuous gas analyzer can measure the CO and CO2 in emissions simultaneously.
The Ultramat 23 uses the principle of infrared absorption.
Several versions with different ranges are available.
The machine can be delivered with its calibration certificate on request (depending on the range).

Specification

– Measurement Ranges:
Item 120 :  0 – 0.05% and 0 – 2.5% CO and 0 – 5% and 0 – 25% CO2
Item 121 : 0 to 1000 ppm CO and 0 to 10,000 ppm CO2 (full scale)
Item 122 : 0 – 10% and 0 – 50% CO and 0 – 1% CO2
– Units : %, mg/m3
– Detection limit : 50 ppm CO / 500 ppm CO2
Item 120 : 50 ppm CO / 500 ppm CO2
Item 121 : 1 ppm CO / 1 ppm CO2
Item 122 : 0.05% ppm CO / 500 ppm CO2
– Data storage : none (a data recorder can be added).
– Internal Pump : yes
– Analog Output : 0 – 10 V
– Packaged weight : 15 kg
– Number of packages : 1
– Recommended for use with : 846, 832, 820, 622, 923, 924.

Key Points

– 19’’ rack, 4U

Heated probes item 845 et 846

Heated portable sampling probe with filter.
Fitted with a ceramic filter and a 60 cm long, 6 mm diameter stainless steel tube.

Specification

– Stainless steel probe
– Sampling temperature: 600 °C max.
– 2μm ceramic filter
– Heats up to 180°C
– Packaged weight 5 kg, 1 package
– Recommended for use with: 831, 834, 822

 

Key Points

– NOT SUITABLE FOR SAFETY CLASS AREAS

42i item 233

This machine can measure NO, NO2 and NOx.
The Thermo 42i uses the principle of chemiluminescence.
It alternately measures NO (directly) and then NOx (via the converter).
It displays the 3 parameters continuously, for NO, NO2 and NOx.
It can be used after a dilution system on a high concentration application (such as emissions).

Specification

– Measurement Range : programmable from 0 – 0.05 ppm to 0 – 100 ppm.
– Units : ppb or mg/m3 programmable
– Detection Limit : 0.4 ppb
– Data storage : 5000 measurement points
– Internal Pump : yes
– Analog Output : yes
– Communication interface : yes
– Software : Yes
– Packaged weight : 28 kg
– Number of packages : 1
– Recommended for use with : 622, 843, 921P, 927.

Key Points

– Menus for setting parameters and optical and electronic diagnostics
– Automatic range switchover
– Fast response time, linearity on all ranges
– Reduced sensitivity to interference
– TCPIP Ethernet Connection

Dusts item 311 et 311A

This isokinetic manual sampling system will continuously sample gas or vapor in a chimney while maintaining the same speed characteristics as at the sampling point. Particles are removed onto a filter. Hot gases are conditioned in a series of cold bubblers.

Condensate is recovered and a volume flowmeter (DGM) measures the dry gas flowrate.

This system can either be supplied with a heating cabinet or with a Cateco oven box which reduces its overall size.

Specification

– Sampling flow rate : depending on the isokinetic parameters < 40 liters/min
– Length of probe : 0.6 m, 0.9 m, 1.2 m, 1.5 m, 1.8 m, stainless steel (specify length with order).
– Umbilical : 7.5 m, 15 m or 30 m (specify with order).
– Set of Nozzles : 3, 4, 5, 7, 9 and 12 mm (stainless steel).
– Gas Temperature : 200 °C max (optionally 600 °C max).
– Oven Temperature : 120 °C
– Calculation Sheet : in Excel® (supplied)
– Packaged weight : 120 kg
– Number of packages : 5

 

Key Points

– Item 311A (Cateco oven box) is particularly suited for difficult sampling operations with its small probe and small oven compartment.
– This device must only be used by an operator trained in a specific methodology. The flow speed at the sampling point must be known and communicated to CleanAir Europe for assessing the feasibility of the project.

Gas Cylinders Item 916 to 929S

Gas cylinders are delivered with a stainless steel or brass AFNOR type C or E pressure reducing valve connector.
Consumption is calculated from the difference in incoming and outgoing pressure, corrected for temperature.
CleanAir can provide a wide range of working standard gases (contact us for more details).
These gases are dispatched with a hazardous material declaration.

Pure gases and standard work gases are certified.

Article      Compound
916          NH3/N2
917          N2O/N2
920          O2/CO2/CO/SO2
921          NO/N2
921P        NO/N2 in ppb
922          SO2/N2
922P        SO2/N2 in ppb
923          CO/N2
924          CO2/O2/N2
924P        CO2/N2 in ppb
925          C3H8/N2
925A        C3H8/AIR
925M       CH4/N2
925MA     CH4/AIR
926         N2 100% (5.0)
927         Air
928         H2 100% (5.0)
928H       H2/He 40/60%
929         HCl/N2
929I        I-C4H8/N2
929N      NO2/N2
929S      H2S/N2

 

Gas Cylinders

– Packaged Weight: 15 kg (B11), 1 package per cylinder with safety marking

Pressure-reducing valves by themselves

– Ref. 931: double stage stainless steel C connector
– Ref. 932: double stage brass C or E connector (specify when ordering)
– Packaged weight: 3 kg, 1 box

AP 360 item 220

This machine measures CO in the open air to determine air quality or to set a zero baseline before building construction work is carried out.
The Horiba AP360 uses NDIR detection.

Specification

– Measurement Range : 0 – 100 ppm
– Units : ppm
– Detection Limit : 0.02 ppm
– Data storage : Yes
– Internal pump : yes
– Analog output : Yes
– Communication interface : yes
– Packaged weight : 20 kg
– Number of packages : 1
– Recommended for use with : 622, 923, 927.

Key PointsPoints clés

– 19’’ rack

Mini Mite item 141

This machine will convert H2S and TRS into SO2.
The Thermo Mini- Mite uses a thermal oxidation chamber to do this.
The temperature is adjustable depending on the gas to be converted:
– H2S: 650 °C
– TRS: 850 °C

Specification

– Utilization Range : 0 – 1100 °C
– Conversion Range : 0 – 50 ppm H2S
– Yield : > 95%
– Units : °C
– Resolution : 1°C
– Packaged weight : 10 kg
– Number of packages : 2
– Recommended for use with : 250, 235.